Home>FPV Drone and Part>Holybro Remote ID WIFI / Bluetooth-Compatible Supported in PX4 / Ardupilot CAN Serial Protocol For RC Model Drone Airplane

Holybro Remote ID WIFI / Bluetooth-Compatible Supported in PX4 / Ardupilot CAN Serial Protocol For RC Model Drone Airplane Item NO.: 40099970

Write a Review

US$ 18.35

Color:
	US$ 24.65	Stock(99)	- +
	US$ 18.35	Stock(99)	- +

Quantity: 0 , Subtotal 0

Product Name	Holybro Remote ID WIFI / Bluetooth-Compatible Supported in PX4 / Ardupilot CAN Serial Protocol For RC Model Drone Airplane
Item NO.	40099970
Weight	0.05 kg = 0.1102 lb = 1.7637 oz
Category	FPV Drone and Part
Brand	Holybro
Creation Time	2023-12-20

Holybro RemoteID Module is low cost, small size, and light weight module that broadcast information about UAVs in flight through WIFI & Bluetooth-Compatible. It supports both CAN and serial protocols. It is a FCC & CE approved radio module.

Note: This product is designed for the Standard Remote ID Solution, primarily targeting drone manufacturers and system integrators, as you need to do your own approval process at the FAA (DoC submission) if you are in the USA. For the most accurate and latest information related to this topic, please refer to the official governance website of your country.

Specification

Radio module:
- Espressif ESP-C3 module
- Bluetooth and WiFi 2.4GHz (ERP): + 20 dBm (100 mW)
- FCC & CE certified radio module
Firmware:
- ArduRemoteID (https://github.com/ArduPilot/ArduRemoteID).
- Supports upgrading firmware via the web interface (“OTA”)
Supported in PX4 & Ardupilot
Protocol: CAN & Serial
Interface:
- 1x JST GH 4-pin CAN (CAN) port
- 1x JST GH 6-pin TELEM (UART) port
Antenna Connector type:
- On CNC Case: SMA connector
- On PCB: IPEX Connector
Range: > 5km detection range*
Power: 5V supplied from TELEM or CAN port
LED lights: Bright RGB status LED
Size:
- Without case: 35.3 x 23.5 mm (not including antenna)
- With CNC case: 38 x 26.5 x 11.5 mm (not including antenna)
Mount: M2 screws
Operating temperature: -40°C to +85°C
Weight:
- PCB only: 4 g
- With CNC case & Antenna: 27.5g
- Without case & Antenna: 16.5g (Cable 20cm)
Certification: FCC& CE

* The detection range depends on many factors such as the receiver antenna gain, transmission protocol, weather conditions, flying height, receiver height line of sight etc. With professional receivers a range of 5 km and more is possible.

SHOP ALL CATEGORIES

Holybro Remote ID WIFI / Bluetooth-Compatible Supported in PX4 / Ardupilot CAN Serial Protocol For RC Model Drone Airplane Item NO.: 40099970

Holybro RemoteID Module is low cost, small size, and light weight module that broadcast information about UAVs in flight through WIFI & Bluetooth-Compatible. It supports both CAN and serial protocols. It is a FCC & CE approved radio module.

Specification

Radio module:

Espressif ESP-C3 module

Bluetooth and WiFi 2.4GHz (ERP): + 20 dBm (100 mW)

Firmware:

ArduRemoteID (https://github.com/ArduPilot/ArduRemoteID).

Supports upgrading firmware via the web interface (“OTA”)

Supported in PX4 & Ardupilot

Protocol: CAN & Serial

Interface:

1x JST GH 4-pin CAN (CAN) port

1x JST GH 6-pin TELEM (UART) port

Antenna Connector type:

On CNC Case: SMA connector

On PCB: IPEX Connector

Range: > 5km detection range*

Power: 5V supplied from TELEM or CAN port

LED lights: Bright RGB status LED

Size:

Without case: 35.3 x 23.5 mm (not including antenna)

With CNC case: 38 x 26.5 x 11.5 mm (not including antenna)

Mount: M2 screws

Operating temperature: -40°C to +85°C

Weight:

PCB only: 4 g

With CNC case & Antenna: 27.5g

Without case & Antenna: 16.5g (Cable 20cm)

Certification: FCC& CE

* The detection range depends on many factors such as the receiver antenna gain, transmission protocol, weather conditions, flying height, receiver height line of sight etc. With professional receivers a range of 5 km and more is possible.

Package Includes：

1x Remote ID

1x Antenna

1x JST GH 6pin 150mm Cable

1x JST GH 4pin 150mm Cable

You May Also Like

Recently Viewed

Subscribe To Our Newsletter

Join our community